Make a Garden Seat for your Doll 1.6 scale

How to make a garden seat for your doll using lollipop sticks and a glue gun. This took me an afternoon to make and I only needed to make a cut on 4 lollipop sticks (4 halves for the seat’s front legs and 4 halves for the seats). The rest were used singly by placing and gluing together. A total of 56 lollipop sticks were used. There wasn’t much measuring involved and I did a lot of this by eye, but I did take photos for each step in case anyone else would care to make their own.

I started by finding a picture of a garden seat that I wanted, purely to give me an idea of the structure. I soon realised that if I wanted to copy the seat in the photo exactly that I’d need to make several cuts, so I changed the design as I went along. I decided to make 2 wide chairs and join them together (somehow). I made both the chairs at the same time instead of one chair and then the next. So for each step that is listed below, I did twice before doing the next step.

Chair Back

For each chair there are 2 rear uprights that are the length of 2 lollipop sticks. The 2 sticks are joined together by overlapping with a 3rd stick. So each upright uses 3 sticks. Be sure to measure the overlapping stick at the halfway mark as this is important to make the chair sit evenly.

The uprights have 2 horizontal supporting bars.

They also have 3 more sticks for the headrest.

Chair Seat

Each chair uses 5 lollipop sticks with 1 cut in half. The image below is showing 2 in half to be ready for making both chairs.

1. Glue the 2 halves to one stick, at right angles on each end.

2. Glue another stick to the other ends (making a rectangle).

3. Glue 3 more sticks in the centre as horizontal slats.

Fix Chair Seat to Chair Back

This is where it can get a bit tricky so best not to rush it. When I placed the chair seat onto the chair back I realised that it needed a horizontal bracing bar to help keep it in place. (I had measured the doll’s legs beforehand and knew that I wanted the seat to be 6 cm above the floor).

4. Mark 6cm up from the bottom of the chair back and glue a stick horizontally across from back leg to back leg.

5. Glue the chair seat at right angles, onto the bracing bar.

Front Legs

This part uses 2 lollipop sticks with 1 full length and 1 cut into 2 halves. It’s basically a long C-shape.

6. Glue the 2 halves to the full length stick, at right angles to both ends of the stick.

Fix Front Legs to Chair

This is also a bit fiddly. I rested the chair piece upside down onto the edge of my work table.

7. Put some hot glue onto the chair legs, place the C-piece firmly onto the chair seat (front), holding in place until glue sets.

At this stage I could see the garden seat taking on a bit of shape so simply had to try it out on Joy #Kruseling.

I also had to figure out the best way to join both seats together. I decided that setting them at right angles would be best. This is where the glue went where I didn’t want it to and I ended up with a bog blob, which I left there until the very end before I removed it (it helped keep it in place…..).

Canopy

The idea for this only came to me after I had made the seats. It was the challenge of fixing the 2 seats together that made me think of how to make the canopy, as it needed to help stabilize the whole structure. I used 11 lollipop sticks for the canopy, starting with a T-bar and then fanning out the other sticks so they would span both chairs. I placed the lollipop sticks on the table in a rough shape, holding the chair piece upside down over it, to be sure the size was right. This was also how I placed the canopy when gluing it to the seat.

The steps are shown in the 5 photos below.

Centre Back

The final part was to match the centre piece to the side pieces. For this part 5 lollipop sticks were glued to the back rests as shown in the 2 photos below.

Finish

All that was left was to snip the big dollop of glue off of the chair legs and no matter how tidy I was trying to be with my gluing there were glue strands in places that needed picking off too. It was ready for painting!

Here it is after one coat of garden fence paint and with Joy sitting comfortably in the sunshine.

I think it would make an ideal gift for any small doll lover. As well as Kruselings, this size also fits a seated Barbie. If you have a go and make a garden seat for your doll then do please send me a photo – I’d love to see it!